Remove errant backticks

- Changes from JC (thanks) and also make sure descriptions fit in with Master->Primary and Slave->Secondary [SME: 13069]
  Also write descriptive paragraph as no-one else has!
  Also also, incorporate newly auditted lex file

createlinks

@@ -2,23 +2,39 @@
 
 use esmith::Build::CreateLinks  qw(:all);
 
-my @events = qw(bootstrap-console-save console-save post-install post-upgrade smeserver-nutUPS-update);
+my @events = qw(bootstrap-console-save console-save post-install post-upgrade smeserver-nutUPS-update nut-conf);
 
-templates2events("/etc/sysconfig/ups", @events);
-templates2events("/usr/lib/systemd/system/nut-server.service.d/50koozali.conf", @events);
-templates2events("/usr/lib/systemd/system/nut-monitor.service.d/50koozali.conf", @events);
 
-foreach (qw(ups.conf upsd.users upsmon.conf upssched.conf))
+foreach (qw(nut.conf ups.conf upsd.users upsmon.conf upssched.conf))
 {
     templates2events("/etc/ups/$_", @events);
 }
 
-foreach (qw(bootstrap-console-save console-save smeserver-nutUPS-update))
+foreach (qw(bootstrap-console-save console-save smeserver-nutUPS-update nut-conf))
 {
     templates2events("/etc/ups/upsd.conf", $_);
 }
 
-my $event="smeserver-nutUPS-update";
+event_link("nut-config", "post-upgrade" , "04");
-safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut");
+event_link("nut-config-drivers", "post-upgrade", "50");
+
+my $event= "nut-conf";
+event_link("nut-config", $event, "04");
+event_link("nut-config-drivers", $event, "50");
+event_link("systemd-default", $event, "88");
+safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut-driver\@ups");
+safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut-monitor");
+safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut-server");
+safe_symlink("restart", "root/etc/e-smith/events/$event/services2adjust/masq");
+templates2events("/etc/rc.d/init.d/masq", $event);
+
+
+$event="smeserver-nutUPS-update";
+safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut-driver\@ups");
+safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut-monitor");
+safe_symlink("try-restart", "root/etc/e-smith/events/$event/services2adjust/nut-server");
 templates2events("/etc/systemd/system-preset/49-koozali.preset", $event);
-event_link("systemd-default", $event, "06");
+templates2events("/etc/rsyslog.conf", $event);
+event_link("nut-config", $event, "04");
+event_link("nut-config-drivers", $event, "50");
+event_link("systemd-default", $event, "88");

root/etc/e-smith/db/configuration/defaults/nut-driver@ups/status

@@ -0,0 +1 @@
+disabled

root/etc/e-smith/db/configuration/defaults/nut-driver@ups/type

@@ -0,0 +1 @@
+service

root/etc/e-smith/db/configuration/defaults/nut-monitor/status

@@ -0,0 +1 @@
+disabled

root/etc/e-smith/db/configuration/defaults/nut-monitor/type

@@ -0,0 +1 @@
+service

root/etc/e-smith/db/configuration/defaults/nut-server/status

@@ -0,0 +1 @@
+disabled

root/etc/e-smith/db/configuration/defaults/nut-server/type

@@ -0,0 +1 @@
+service

root/etc/e-smith/db/configuration/defaults/nut/TCPPort

@@ -0,0 +1 @@
+3493

root/etc/e-smith/db/configuration/defaults/nut/type

@@ -1 +1 @@
-service
+configuration

root/etc/e-smith/db/configuration/migrate/15nutPass

@@ -0,0 +1,22 @@
+{
+    use MIME::Base64 qw(encode_base64);
+
+    my $nutrec = $DB->get('nut') || $DB->new_record('nut', {type => 'service'});
+    # migrate old
+    $nutrec->set_prop('PrimaryPass',$DB->get_prop_and_delete('nut', MasterPass)) if (exists $nut{'MasterPass'}); 
+    $nutrec->set_prop('SecondaryPass',$DB->get_prop_and_delete('nut', SlavePass)) if (exists $nut{'SlavePass'});
+
+    $nutrec->set_prop('PrimaryPass', sprintf("%15.0f", int( (1000000000000000) * rand() ))) if not $nutrec->prop('PrimaryPass');
+    $nutrec->set_prop('SecondaryPass', sprintf("%15.0f", int( (1000000000000000) * rand() ))) if not $nutrec->prop('SecondaryPass');
+    $nutrec->set_prop('AdminPass', sprintf("%15.0f", int( (1000000000000000) * rand() ))) if not $nutrec->prop('AdminPass');
+
+    # if $nut{SlaveUPS} defined we set and the target not existing ClientUPS ; then delete SlaveUPS
+    # set ClientUser as upsslave (was the content before sme11) intended for smooth migration
+    # set ClientPass as $nut{SlavePass}/{SecondaryPass}  
+    if ( $nut{'SlaveUPS'} ) {
+	$nutrec->set_prop('ClientUPS',$DB->get_prop_and_delete('nut','SlaveUPS') ) if not $nut{'ClientUPS'};
+	$nutrec->set_prop('ClientUser','upsslave');
+        $nutrec->set_prop('ClientPass',$nutrec->prop('SecondaryPass'));
+	}
+
+}

root/etc/e-smith/db/configuration/migrate/20nutMigrate

@@ -0,0 +1,22 @@
+{
+  # migrate to SME11
+  # first we get ride of Master=no
+  # if Mode  not set then set it according to Master
+  my $mnut = $DB->get('nut') || $DB->new_record('nut', {type => 'service'});
+  my $nutMaster = $DB->get_prop_and_delete ('nut','Master');
+  unless ( ${'nut'}{'Mode'} ) {
+    $mnut>set_prop('Mode','netserver') if $nutMaster eq "yes";
+  }
+
+  # if nut-driver@ups not existing create it
+  my $driverUPS = $DB->get('nut-driver@ups') || $DB->new_record('nut-driver@ups', {type => 'service'});
+  # then migrate to nut-driver@ups (first UPS) the following properties
+  my $mdl = $DB->get_prop_and_delete ('nut','mdl');
+  $driverUPS->set_prop('mdl',$mdl) unless ${'nut-driver@ups'}{'mdl'};
+  my $mfr = $DB->get_prop_and_delete ('nut','mfr');
+  $driverUPS->set_prop('mfr',$mfr) unless ${'nut-driver@ups'}{'mfr'};
+  my $model = $DB->get_prop_and_delete ('nut','Model');
+  $driverUPS->set_prop('Model',$model) unless ${'nut-driver@ups'}{'Model'};
+  my $Type = $DB->get_prop_and_delete ('nut','Type');
+  $driverUPS->set_prop('Type',$model) unless ${'nut-driver@ups'}{'Type'};
+}

root/etc/e-smith/db/configuration/migrate/nutPass

@@ -1,8 +0,0 @@
-{
-    use MIME::Base64 qw(encode_base64);
-
-    my $nutrec = $DB->get('nut') || $DB->new_record('nut', {type => 'service'});
-    $nutrec->set_prop('MasterPass', sprintf("%15.0f", int( (1000000000000000) * rand() ))) if not $nutrec->prop('MasterPass');
-    $nutrec->set_prop('SlavePass', sprintf("%15.0f", int( (1000000000000000) * rand() ))) if not $nutrec->prop('SlavePass');
-    $nutrec->set_prop('AdminPass', sprintf("%15.0f", int( (1000000000000000) * rand() ))) if not $nutrec->prop('AdminPass');
-}

root/etc/e-smith/events/actions/nut-config

@@ -0,0 +1,52 @@
+#!/bin/bash
+
+# this script is called before template-expand
+# then another script is called to run /usr/libexec/nut-driver-enumerator.sh and start/stop drivers
+# then traditionnal services2adjust
+
+# calling this script to configure unit and drivers
+if [[ $(/sbin/e-smith/config getprop nut status || echo "disabled") == "disabled" ]] ; then
+  # disable server
+  /sbin/e-smith/config setprop nut-server status disabled
+  /sbin/e-smith/config setprop nut access localhost
+  # disable monitor
+  /sbin/e-smith/config setprop nut-monitor status disabled
+  # TODO get_all_by_prop filter nut-driver@ and foreach $UPS disabled
+  #config keys|grep nut-driver
+  for OUTPUT in $(/sbin/e-smith/config keys|grep nut-driver)
+  do
+    /sbin/e-smith/config setprop $OUTPUT status disabled
+  done
+
+  exit 0;
+fi
+# nut is enabled
+
+# we set services depending on Mode
+Mode=$(/sbin/e-smith/config getprop nut Mode || echo "standalone")
+if [[ $Mode == "netserver" ]] ; then
+    /sbin/e-smith/config setprop nut-server status enabled
+    /sbin/e-smith/config setprop nut access private
+elif [[ $Mode == "netclient" ]] ; then
+    /sbin/e-smith/config setprop nut-server status disabled
+    /sbin/e-smith/config setprop nut access localhost
+else
+    /sbin/e-smith/config setprop nut-server status enabled
+    /sbin/e-smith/config setprop nut access localhost
+fi
+# enable nut-monitor
+/sbin/e-smith/config setprop nut-monitor status enabled
+
+# get_all_by_prop filter nut-driver@ and foreach $UPS enable.
+if [[ $Mode == "netclient" ]] ; then
+  for OUTPUT in $(/sbin/e-smith/config keys|grep nut-driver)
+  do
+    /sbin/e-smith/config setprop $OUTPUT status disabled
+  done
+else
+  for OUTPUT in $(/sbin/e-smith/config keys|grep nut-driver)
+  do
+    /sbin/e-smith/config setprop $OUTPUT status enabled
+  done
+fi
+

root/etc/e-smith/events/actions/nut-config-drivers

@@ -0,0 +1,45 @@
+#!/bin/bash
+
+# another script is called before template-expand to set services
+# this script is called to run /usr/libexec/nut-driver-enumerator.sh and start/stop drivers
+# then traditionnal services2adjust
+
+# enumerate / configure drivers
+/usr/libexec/nut-driver-enumerator.sh 2>/dev/null
+
+event=$1
+
+if [[ $i == "post-upgrade" ]] ; then 
+	exit 0
+fi
+
+if [[ $i == "bootstrap-console-save" ]] ; then
+        exit 0
+fi
+
+# if disabled stop them
+if [[ $(/sbin/e-smith/config getprop nut status || echo "disabled") == "disabled" ]] ; then
+	# if disabled stop them 
+	for OUTPUT in $(/sbin/e-smith/config keys|grep nut-driver)
+	 do
+	    /usr/bin/systemctl stop $OUTPUT
+	done
+      	exit 0
+fi
+
+# if netclient stop them
+if [[ $(/sbin/e-smith/config getprop nut Mode || echo "netclient") == "netclient" ]] ; then
+  # if disabled stop them 
+  for OUTPUT in $(/sbin/e-smith/config keys|grep nut-driver)
+   do
+      /usr/bin/systemctl stop $OUTPUT 2>/dev/null
+  done
+        exit 0
+fi
+
+
+# if we are there we want to restart / start them
+for OUTPUT in $(/sbin/e-smith/config keys|grep nut-driver)
+ do
+    /usr/bin/systemctl restart $OUTPUT
+done

root/etc/e-smith/templates/etc/etc/rsyslog.conf/32nut

@@ -0,0 +1,5 @@
+#nut / UPS we only use journalctl
+:programname, isequal, "nut-monitor" stop
+:programname, isequal, "nut-server" stop
+:programname, startswith, "nut-driver" stop
+

root/etc/e-smith/templates/etc/sysconfig/ups/MODEL

@@ -1 +0,0 @@
-MODEL=upsdrvctl

root/etc/e-smith/templates/etc/sysconfig/ups/SERVER

@@ -1 +0,0 @@
-SERVER={ $nut{Master} || 'yes' }

root/etc/e-smith/templates/etc/systemd/system-preset/49-koozali.preset/70nutUPS

@@ -1,16 +1,26 @@
 # nut UPS specific subservices
 {
 $nutstatus = $nut{status} || 'disabled';
-$master = $nut{Master} || 'yes';
+$mode = $nut{Mode} || 'standalone';
+my @upses = grep(/^nut-driver\@[a-zA-Z0-9_-]+$/, $DB->keys);
 
 if ($nutstatus eq 'enabled') {
-	$OUT .= "enable	nut-server.service\n" if ($master eq  'yes');
+        $OUT .= "enable nut-server.service\n" if ($mode ne 'netclient');
-	$OUT .= "disable nut-server.service\n" unless ($master eq  'yes');
+        $OUT .= "disable nut-server.service\n" unless ($mode eq 'netclient');
-	$OUT .= "enable	nut-monitor.service\n";
+        $OUT .= "enable nut-monitor.service\n";
+        foreach my $ups ( sort {$a cmp $b} @upses )
+        {
+          $OUT .= "enable $ups.service\n";
+        }
   }
 else
   {
         $OUT .= "disable nut-server.service\n";
         $OUT .= "disable nut-monitor.service\n";
+        foreach my $ups ( sort {$a cmp $b} @upses )
+        {
+          $OUT .= "disable $ups.service\n";
+        }
   }
 }
+

root/etc/e-smith/templates/etc/ups/nut.conf/10MODE

@@ -0,0 +1,7 @@
+# mode could be none|standalone|netserver|netclient
+MODE={
+ return "none" unless ( ($nut{"status"}||"disabled") eq "enabled");
+ # if Master no => netclient
+ # if Master yes => standalone or netserver
+ $nut{Mode} || "standalone";
+}

root/etc/e-smith/templates/etc/ups/nut.conf/20ALLOW_NO_DEVICE

@@ -0,0 +1,10 @@
+
+# Uncomment this to allow starting the `upsd` data server even if `ups.conf`
+# has no device sections configured at the moment. This environment variable
+# overrides the built-in "false" flag in `upsd`, and an optional same-named
+# default flag that can be set in `upsd.conf`. If you want a data server always
+# running, even if it initially has nothing to serve (may be live-reloaded
+# later, when devices become configured), this option is for you.
+#ALLOW_NO_DEVICE=true
+#export ALLOW_NO_DEVICE
+

root/etc/e-smith/templates/etc/ups/nut.conf/30ALLOW_NOT_ALL_LISTENERS

@@ -0,0 +1,11 @@
+
+# Uncomment this to allow starting the `upsd` data server even if not all
+# `LISTEN` directives can be honoured at the moment. This environment variable
+# overrides the built-in "false" flag in `upsd`, and an optional same-named
+# default flag that can be set in `upsd.conf`. If you want a data server always
+# running, even if it would potentially not serve all clients on every uptime,
+# this option is for you (note you would have to restart `upsd` to pick up the
+# `LISTEN`ed IP address if it appears later). Probably `LISTEN *` is better.
+#ALLOW_NOT_ALL_LISTENERS=true
+#export ALLOW_NOT_ALL_LISTENERS
+

root/etc/e-smith/templates/etc/ups/nut.conf/40UPSD_OPTIONS

@@ -0,0 +1,6 @@
+
+# The optional 'UPSD_OPTIONS' allow to set upsd specific command-line options.
+# It is ignored when 'MODE' above indicates that no upsd should be running.
+# It may be redundant in comparison to options which can be set in `upsd.conf`.
+#UPSD_OPTIONS=
+

root/etc/e-smith/templates/etc/ups/nut.conf/50UPSMON_OPTIONS

@@ -0,0 +1,6 @@
+
+# The optional 'UPSMON_OPTIONS' allow to set upsmon specific command-line options.
+# It is ignored when 'MODE' above indicates that no upsmon should be running.
+# It may be redundant in comparison to options which can be set in `upsmon.conf`.
+#UPSMON_OPTIONS=
+

root/etc/e-smith/templates/etc/ups/nut.conf/60POWEROFF_WAIT

@@ -0,0 +1,9 @@
+
+# If the optional 'POWEROFF_WAIT' is configured (to a value that can be handled
+# by `/bin/sleep` on the current system - typically an integer with the number
+# of seconds for a delay, but not always limited to that syntax), and the current
+# system which manages one or more UPS devices would not only command it to shut
+# down, but also try to avoid the "Power race". Caveats emptor, see NUT FAQ and
+# other docs for details.
+#POWEROFF_WAIT=3600
+

root/etc/e-smith/templates/etc/ups/nut.conf/70POWEROFF_QUIET

@@ -0,0 +1,8 @@
+
+# The optional 'POWEROFF_QUIET' setting controls if the NUT shutdown integration
+# scripts or service units would emit messages about their activity (or lack
+# thereof). By default they may be verbose, to aid post-mortem troubleshooting
+# via logs or console captures.
+# Set to `true` to avoid that trove of information, if you consider it noise.
+#POWEROFF_QUIET=true
+

root/etc/e-smith/templates/etc/ups/ups.conf/UPS

@@ -1,16 +1,28 @@
 {
-    my $model = $nut{Model} || "usbhid-ups";
+   my $poll = $nut{pollInterval} || '2';
-    my $device = $nut{Device} || "/var/lib/ups/hiddev0";
+   if ($poll ne '2') {
-    my $type = $nut{Type};
+     $OUT .= "pollinterval = $poll\n";
-    my $mfr = $nut{mfr};
+   }
-    my $mdl = $nut{mdl};
+
-    $OUT .= "[UPS]\n";
+    my @upses = grep(/^nut-driver\@[a-zA-Z0-9_-]+$/, $DB->keys);
-    $OUT .= "\tdriver = $model\n";
+    foreach my $ups ( sort {$a cmp $b} @upses )
-    if  ($model eq 'genericups')
+	{
-    { 
+		my $status = ${"$ups"}{status} || "disabled";
-      $OUT .= "\tupstype = $type\n" if defined $type;
+		next if $status eq "disabled";
-      $OUT .= "\tmfr = $mfr\n" if defined $mfr;
+		my ($name )= $ups =~ /^nut-driver\@(.*)$/ ;
-      $OUT .= "\tmodel = $mdl\n" if defined $mdl;
+		my $model = ${"$ups"}{Model} || "usbhid-ups";
-    }
+		my $device = ${"$ups"}{Device} || "auto"; #"/var/lib/ups/hiddev0";
-    $OUT .= "\tport = $device\n";
+		my $type = ${"$ups"}{Type};
+		my $mfr = ${"$ups"}{mfr};
+		my $mdl = ${"$ups"}{mdl};
+		$OUT .= "[$name]\n";
+		$OUT .= "\tdriver = $model\n";
+		if  ($model eq 'genericups')
+		{ 
+			$OUT .= "\tupstype = $type\n" if defined $type;
+			$OUT .= "\tmfr = $mfr\n" if defined $mfr;
+			$OUT .= "\tmodel = $mdl\n" if defined $mdl;
+		}
+		$OUT .= "\tport = $device\n";
+	}
 }

root/etc/e-smith/templates/etc/ups/upsd.users/monitor

@@ -1,8 +1,18 @@
+       [upsprimary]
+               password  = { $nut{PrimaryPass} }
+               upsmon primary
+
+       [upssecondary]
+               password  = { $nut{SecondaryPass} }
+               upsmon secondary
+{
+# we keep those two for backward compatibility pre SME11
+}
        [upsmaster]
-               password  = { $nut{MasterPass} }
+               password  = { $nut{PrimaryPass} }
-               upsmon master
+               upsmon primary
 
        [upsslave]
-               password  = { $nut{SlavePass} }
+               password  = { $nut{SecondaryPass} }
-               upsmon slave
+               upsmon secondary
 

root/etc/e-smith/templates/etc/ups/upsmon.conf/MONITOR

@@ -1,7 +1,14 @@
 {
-    if ( ($nut{Master} || 'yes') ne 'no' ) {
+	if ( ($nut{Mode} || 'standalone') eq 'netclient' ) {
-	$OUT = "MONITOR UPS\@localhost 1 upsmaster $nut{MasterPass} master";
+		$OUT = "MONITOR $nut{ClientUPS} 1  $nut{ClientUser}  $nut{ClientPass} secondary";
-    } else {
+	} else {
-	$OUT = "MONITOR $nut{SlaveUPS} 1 upsslave $nut{SlavePass} slave";
+		my @upses = grep(/^nut-driver\@[a-zA-Z0-9_-]+$/, $DB->keys);
-    }
+		my $size = scalar(@upses);
+		foreach my $ups ( sort {$a cmp $b} @upses )
+		{
+			my ($upsname) = $ups =~ /^nut-driver\@([a-zA-Z0-9_-]+)$/ ; 
+			$OUT .= "MONITOR $upsname\@localhost 1 upsprimary $nut{PrimaryPass} primary";
+			$OUT .= "\n" if --$size >=1;
+		}
+	}
 }

root/usr/lib/systemd/system/nut-driver.service.d/51koozali.conf

@@ -1,14 +0,0 @@
-#------------------------------------------------------------
-#	       !!DO NOT MODIFY THIS FILE!!
-# 
-# Manual changes will be lost when this file is regenerated.
-#
-# Please read the developer's guide, which is available
-# at http://www.contribs.org/development/
-#
-# Copyright (C) 1999-2006 Mitel Networks Corporation
-#------------------------------------------------------------
-
-[Service]
-ExecStartPre=
-ExecStartPre=-/usr/bin/systemd-tmpfiles --create /usr/lib/tmpfiles.d/nut-run.conf

root/usr/lib/systemd/system/nut-driver@.service.d/51koozali.conf

@@ -0,0 +1,4 @@
+[Service]
+ExecStartPre=/sbin/e-smith/service-status %N
+[Install]
+WantedBy= sme-server.target

root/usr/lib/systemd/system/nut-monitor.service.d/50koozali.conf

@@ -0,0 +1,4 @@
+[Service]
+ExecStartPre=/sbin/e-smith/service-status nut-monitor
+[Install]
+WantedBy=sme-server.target

root/usr/lib/systemd/system/nut-server.service.d/50koozali.conf

@@ -0,0 +1,4 @@
+[Service]
+ExecStartPre=/sbin/e-smith/service-status nut-server
+[Install]
+WantedBy=sme-server.target

root/usr/share/smanager/lib/SrvMngr/Controller/Nutups-Custom.pm

@@ -7,22 +7,12 @@
 #
 use esmith::util;
 use esmith::util::network;
-use esmith::ConfigDB;
+use esmith::ConfigDB::UTF8;
-use esmith::HostsDB;
-use esmith::AccountsDB;
-use esmith::NetworksDB;
-use esmith::DomainsDB;
 
 use constant FALSE => 0;
 use constant TRUE  => 1;
 
-
+our $cdb;
-#The most common ones
-my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
-#our $adb = esmith::AccountsDB->open() || die("Couldn't open Accounts db");
-#our $ndb = esmith::NetworksDB->open() || die("Couldn't open Network db");
-#our $hdb = esmith::HostsDB->open() 	  || die("Couldn't open Hosts db");
-#our $ddb = esmith::DomainsDB->open()  || die("Couldn't open Domains db");
 
 # Validation routines - parameters for each panel
 
@@ -49,8 +39,11 @@ my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
 			{$ret .= 'Validation for status failed';}	
 		if (! TRUE) #validate $c->param('Nutmode')
 			{$ret .= 'Validation for Nutmode failed';}
+		#do we want the Slave validated ? we should just display read only	
 		if (! TRUE) #validate $c->param('SlaveUPS_Name')
 			{$ret .= 'Validation for SlaveUPS_Name failed';}
+		if (! TRUE) #validate $c->param('ClientUPS_Name')
+			{$ret .= 'Validation for ClientUPS_Name failed';}	
 		if (! TRUE) #validate $c->param('MasterUPS_Name')
 			{$ret .= 'Validation for MasterUPS_Name failed';}	
 		if (! TRUE) #validate $c->param('UPS_Model')
@@ -73,11 +66,15 @@ my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
 	sub get_data_for_panel_STATUS {
 		# Return a hash with the fields required which will be loaded into the shared data 
 		my $c = shift;
+		$cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
 		my %ret = (
 			#'Data1'=>'Data for STATUS', #Example
 			# fields from Inputs in STATUS $fields['STATUS']
 			'UPSStatus'=>$c->get_ups_status(),
-			'ups_data' => $c->get_ups_status_as_hash()
+			'ups_data' => $c->get_ups_status_as_hash(),
+			'Nutmode'=>$cdb->get_prop('nut', 'Mode')||"none",
+			'localip'=>$cdb->get_value('LocalIP'),
+			'SlaveUPS_Pass'=>$cdb->get_prop('nut', 'SecondaryPass'),
 		);
 		return %ret;
 	}
@@ -85,19 +82,24 @@ my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
 	sub get_data_for_panel_CONFIG {
 		# Return a hash with the fields required which will be loaded into the shared data 
 		my $c = shift;
-		$cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
+		$cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
 		my %ret = (
 			'Data1'=>'Data for CONFIG', #Example
+			'localip'=>$cdb->get_value('LocalIP'),
 			# fields from Inputs in CONFIG $fields['CONFIG']
-			'status'=>$cdb->get_prop('nut', 'status', 'disabled'),
+			'status'=>$cdb->get_prop('nut', 'status') || 'disabled',
-			'Nutmode'=>$cdb->get_prop('nut', 'mode', 'standalone'),
+			'Nutmode'=>$cdb->get_prop('nut', 'Mode') || 'standalone',
-			'SlaveUPS_Name'=>$cdb->get_prop('nut', 'SlaveUPS', 'ups@IPaddress'),
+			'ClientUPS_Name'=>$cdb->get_prop('nut', 'ClientUPS'),
-			'MasterUPS_Name'=>$cdb->get_prop('nut', 'MasterUPS', 'ups@localhost'),
+			'ClientUPS_User'=>$cdb->get_prop('nut', 'ClientUser'),
-			'UPS_Model'=>$cdb->get_prop('nut', 'Model', 'usbhid-ups'),
+			'ClientUPS_Pass'=>$cdb->get_prop('nut', 'ClientPass'),
-			'UPS_Device'=>$cdb->get_prop('nut', 'Device', 'auto'),
+			'SlaveUPS_Pass'=>$cdb->get_prop('nut', 'SecondaryPass'),
-			'UPS_gen_Type'=>$cdb->get_prop('nut', 'Type', ''),
+			'MasterUPS_Name'=>$cdb->get_prop('nut', 'MasterUPS'),
-			'UPS_gen_Mfr'=>$cdb->get_prop('nut', 'mfr', ''),
+			# nut-driver@ups entry
-			'UPS_gen_Model'=>$cdb->get_prop('nut', 'mdl', ''),
+			'UPS_Model'=>$cdb->get_prop('nut-driver@ups', 'Model') || 'usbhid-ups',
+			'UPS_Device'=>$cdb->get_prop('nut-driver@ups', 'Device')|| 'auto',
+			'UPS_gen_Type'=>$cdb->get_prop('nut-driver@ups', 'Type'),
+			'UPS_gen_Mfr'=>$cdb->get_prop('nut-driver@ups', 'mfr'),
+			'UPS_gen_Model'=>$cdb->get_prop('nut-driver@ups', 'mdl'),
 		);
 		return %ret;
 	}
@@ -114,16 +116,16 @@ my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
 		my $c = shift;
 		my $selected = shift; #Parameter is name of selected row.
 		my $is_new_record = shift; #Indicates new record required (defaults)
-		my %ret = {};
+		my %ret = ();
-		return $ret;
+		return %ret;
 	}
 
 	sub get_selected_CONFIG {
 		my $c = shift;
 		my $selected = shift; #Parameter is name of selected row.
 		my $is_new_record = shift; #Indicates new record required (defaults)
-		my %ret = {};
+		my %ret = ();
-		return $ret;
+		return %ret;
 	}
 
 
@@ -137,7 +139,7 @@ my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
 		my $dbkey = 'ChangeThis';
 		# To make it write to DB as comment, delete this (regex) string in each if statement "TRUE\) \#copy or perform with value: .* e.g."
 		
-		if (! TRUE) #copy or perform with value: UPSStatus e.g. $db->set_prop($dbkey,'UPSStatus',$c->param('UPSStatus'),type=>'service'))
+		if (! TRUE) #copy or perform with value: UPSStatus e.g. $db->set_prop($dbkey,'UPSStatus',$c->param('UPSStatus')))
 			{$ret .= 'Perform/save failed for UPSStatus';}
 		if ($ret eq "") {$ret = 'ok';}
 		return $ret;
@@ -147,46 +149,54 @@ my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
 		my $c = shift;
 		my $prefix_data = shift; #Data hash as parameter
 		my $ret = "";
-		$cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
+		$cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
 		my $db = $cdb; #maybe one of the others
 		my $dbkey = 'nut';
+		my $driverkey = 'nut-driver@ups';
 		# To make it write to DB as comment, delete this (regex) string in each if statement "TRUE\) \#copy or perform with value: .* e.g."
 		
-		if (!$db->set_prop($dbkey,'status',$c->param('status'),type=>'service'))
+		if (!$db->set_prop($dbkey,'status',$c->param('status')))
 			{$ret .= 'Perform/save failed for status';}
-		if (!$db->set_prop($dbkey,'mode',$c->param('Nutmode'),type=>'service'))
+		if (!$db->set_prop($dbkey,'Mode',$c->param('Nutmode')))
 			{$ret .= 'Perform/save failed for Nutmode';}
-		if (! $db->set_prop($dbkey,'SlaveUPS',$c->param('SlaveUPS_Name'),type=>'service'))
+
-			{$ret .= 'Perform/save failed for SlaveUPS_Name';}
+		# let only save info regarding the current mode
-		if (! $db->set_prop($dbkey,'MasterUPS',$c->param('MasterUPS_Name'),type=>'service'))
+		# if client mode
+		if (! $db->set_prop($dbkey,'ClientUPS',$c->param('ClientUPS_Name')))
+			{$ret .= 'Perform/save failed for ClientUPS_Name';}
+		if (! $db->set_prop($dbkey,'MasterUPS',$c->param('MasterUPS_Name')))
 			{$ret .= 'Perform/save failed for MasterUPS_Name';}
-		if (! $db->set_prop($dbkey,'SlavePass',$c->param('SlaveUPS_Pass'),type=>'service'))
+		if (! $db->set_prop($dbkey,'ClientUser',$c->param('ClientUPS_User')))
-			{$ret .= 'Perform/save failed for SlaveUPS_Pass';}
+			{$ret .= 'Perform/save failed for ClientUPS_USer';}
-		if (! $db->set_prop($dbkey,'MasterPass',$c->param('MasterUPS_Pass'),type=>'service'))
+		if (! $db->set_prop($dbkey,'ClientPass',$c->param('ClientUPS_Pass')))
-			{$ret .= 'Perform/save failed for MasterUPS_Pass';}
+			{$ret .= 'Perform/save failed for ClientUPS_Pass';}
-		if (! $db->set_prop($dbkey,'Model',$c->param('UPS_Model'),type=>'service'))
+
+		# if not client mode
+		if (! $db->set_prop($driverkey,'Model',$c->param('UPS_Model')))
 			{$ret .= 'Perform/save failed for UPS_Model';}
-		if (! $db->set_prop($dbkey,'Device',$c->param('UPS_Device'),type=>'service'))
+		if (! $db->set_prop($driverkey,'Device',$c->param('UPS_Device')))
 			{$ret .= 'Perform/save failed for UPS_Device';}
-		if (! $db->set_prop($dbkey,'Type',$c->param('UPS_gen_Type'),type=>'service'))
+		if (! $db->set_prop($driverkey,'Type',$c->param('UPS_gen_Type')))
 			{$ret .= 'Perform/save failed for UPS_gen_Type';}
-		if (! $db->set_prop($dbkey,'mfr',$c->param('UPS_gen_Mfr'),type=>'service'))
+		if (! $db->set_prop($driverkey,'mfr',$c->param('UPS_gen_Mfr')))
 			{$ret .= 'Perform/save failed for UPS_gen_Mfr';}
-		if (! $db->set_prop($dbkey,'mdl',$c->param('UPS_gen_Model'),type=>'service'))
+		if (! $db->set_prop($driverkey,'mdl',$c->param('UPS_gen_Model')))
 			{$ret .= 'Perform/save failed for UPS_gen_Model';}
+
+#changes from sme10 to sme11
+# slave/master is changed to secondary/primary (upstream) should bite the bullet rather sooner than latter
+# we move most properties from nut to nut-driver@UPS, nut-driver@UPS1  (we only handle nut-driver@UPS in panel)
+# we remove Master property (redundant)
+# we add mode property, we have 3 modes : 
+# standalone uses primary pass  
+# nethserver uses primary pass
+# netclient uses secondary pass
+
+
+#TODO check if still needed  :
+
 		if ($ret eq "") {
 			$ret = 'ok';
-			#and set Master and access properties according to values
-			if ($db->get_prop($dbkey,"mode",'standalone') eq 'netclient'){
-				$db->set_prop($dbkey,'Master','no',type=>'service');
-			} else {
-				$db->set_prop($dbkey,'Master','yes',type=>'service');
-			}
-			if ($db->get_prop($dbkey,"mode",'standalone') eq 'netserver'){
-				$db->set_prop($dbkey,'access','private',type=>'service');
-			} else {
-				$db->set_prop($dbkey,'access','localhost',type=>'service');
-			}
 			#And run signal-event to apply templates for config files and start task.
 			my @result = qx{/usr/sbin/e-smith/signal-event smeserver-nutUPS-update};
 			if ($? != 0) {
@@ -226,16 +236,17 @@ sub get_model_options {
 
 sub get_ups_status {
 	my $c = shift;
-	$cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
+	$cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
-	my $nutmode = $cdb->get_prop('nut', 'mode','standalone');
+	my $nutmode = $cdb->get_prop('nut', 'Mode') || 'standalone';
 	if ($cdb->get_prop('nut', 'status', 'disabled') eq 'disabled'){
 		return $c->l('nut_status_is_disabled')
-	} elsif ($nutmode eq 'standalone'){
+	} elsif ($nutmode eq 'netclient'){
-		return $c->get_status_from_device($cdb->get_prop('nut','MasterUPS','ups@localhost'));
+    return $c->get_status_from_device($cdb->get_prop('nut','ClientUPS'));
-	} elsif ($nutmode eq 'netserver'){
-		return $c->get_status_from_device($cdb->get_prop('nut','MasterUPS','ups@localhost'));
 	} else {
-		return $c->get_status_from_device($cdb->get_prop('nut','SlaveUPS','apc@192.168.1.99'));
+		# TODO: could enumerate all the upses using
+                # my @upses = grep(/^nut-driver\@[a-zA-Z0-9_-]+$/, $DB->keys);
+                # we will only use the default first one for the moment nut-driver@ups for ups named "ups"
+		return $c->get_status_from_device("ups");
 	}
 }
 

root/usr/share/smanager/lib/SrvMngr/Controller/Nutups.pm

@@ -5,7 +5,7 @@ package SrvMngr::Controller::Nutups;
 #----------------------------------------------------------------------
 # heading     : System
 # description : NutUPS configuration
-# navigation  : 4000 700
+# navigation  : 4000 900
 #
 # name : nutups,    method : get,   url : /nutups,   ctlact : Nutups#main
 # name : nutupsu,   method : post,  url : /nutupsu,  ctlact : Nutups#do_update
@@ -36,11 +36,7 @@ use Data::Dumper;
 
 use esmith::util;
 use esmith::util::network;
-use esmith::ConfigDB;
+use esmith::ConfigDB::UTF8;
-use esmith::AccountsDB;
-use esmith::NetworksDB;
-use esmith::HostsDB;
-use esmith::DomainsDB;
 
 
 
@@ -60,14 +56,7 @@ sub main {
 
     my $c = shift;
     $c->app->log->info( $c->log_req );
-
+    my $cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
-	#The most common ones
-	my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
-	my $adb = esmith::AccountsDB->open() || die("Couldn't open Accounts db");
-	my $ndb = esmith::NetworksDB->open() || die("Couldn't open Network db");
-	my $hdb = esmith::HostsDB->open() 	  || die("Couldn't open Hosts db");
-	my $ddb = esmith::DomainsDB->open()  || die("Couldn't open Domains db");
-
     my %nut_data = ();
     my $title = $c->l('nut_NutUPS_configuration');
     my $modul = '';
@@ -111,15 +100,8 @@ sub do_update {
 	
     my $c = shift;
     $c->app->log->info($c->log_req);
-	my $modul = '';
+    my $modul = '';
-
+    my $cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
-	#The most common ones - you might want to comment out any not used.
-	my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
-	my $adb = esmith::AccountsDB->open() || die("Couldn't open Accounts db");
-	my $ndb = esmith::NetworksDB->open() || die("Couldn't open Network db");
-	my $hdb = esmith::HostsDB->open() 	  || die("Couldn't open Hosts db");
-	my $ddb = esmith::DomainsDB->open()  || die("Couldn't open Domains db");
-
     my %nut_data = ();
     my $title = $c->l('nut_NutUPS_configuration');
 
@@ -220,14 +202,7 @@ sub do_display {
 
     my ($c,$trt) = @_;
     $c->app->log->info($c->log_req);
-
+    my $cdb = esmith::ConfigDB::UTF8->open()   || die("Couldn't open config db");
-	#The most common ones - you might want to comment out any not used.
-	my $cdb = esmith::ConfigDB->open()   || die("Couldn't open config db");
-	my $adb = esmith::AccountsDB->open() || die("Couldn't open Accounts db");
-	my $ndb = esmith::NetworksDB->open() || die("Couldn't open Network db");
-	my $hdb = esmith::HostsDB->open() 	  || die("Couldn't open Hosts db");
-	my $ddb = esmith::DomainsDB->open()  || die("Couldn't open Domains db");
-    
     my %nut_data = ();
     my $title = $c->l('nut_NutUPS_configuration');
     my $modul = "";

root/usr/share/smanager/lib/SrvMngr/I18N/Modules/Nutups/nutups_en.lex

@@ -1,30 +1,29 @@
-#
+'nut_APPLY' => 'Apply',
-# Generated by SM2Gen version: SM2Gen version:0.9(20Jan2025) Chameleon version:4.5.4 On Python:3.12.3 at 2025-01-20 16:21:33
+'nut_ClientUPS_Password' => 'Client UPS password',
-#
+'nut_ClientUPS_Username' => 'Client UPS username',
-'nut_UPS_Generic_Model' => 'UPS Generic Model',
-'nut_UPS_Model' => 'UPS Model',
-'nut_Manage_Nutups-config_settings:' => 'Manage Nutups-config settings',
-'nut_Descriptive_paragraph' => 'Descriptive paragraph',
-'nut_MasterUPS_UPSNAME@IP' => 'UPS name@localhost',
-'nut_SlaveUPS_UPSNAME@IP' => 'Slave->Master UPSNAME@IP',
-'nut_MasterUPS_Password' => Local server password',
-'nut_SlaveUPS_Password' => 'Slaves Password ->Server',
-'nut_Nut_status' => 'Nut status',
-'nut_Configure_NutUPS' => 'Configure NutUPS',
 'nut_CONFIG_panel_action_was_successful' => 'CONFIG panel action was successful',
-'nut_UPS_Generic_Type' => 'UPS Generic Type',
+'nut_Configure_NutUPS' => 'Configure NutUPS',
-'nut_Status_(from_upsc)' => 'Status (from running upsc)',
+'nut_Descriptive_paragraph' => 'You can use your UPS connected directly to your server in a standalone mode or you can act as a Primary whereby other servers can also react to the status of your connected UPS, or you can connect to another server as a Secondary and react to the status of the UPS connected to that server.',
 'nut_Error_Status_Report' => 'Error Status Report',
-'nut_if_Net_Server' => 'Net Server details',
 'nut_if_genericups' => 'Generic UPS details',
 'nut_if_Net_Client' => 'Net Client details',
-'nut_STATUS_panel_action_was_successful' => 'STATUS panel action was successful',
+'nut_if_Net_Server' => 'Net Server details',
+'nut_Manage_Nutups-config_settings:' => 'Manage Nutups configuration settings',
+'nut_MasterUPS_Password' => 'Local server password',
+'nut_MasterUPS_UPSNAME@IP' => 'UPS name@localhost',
 'nut_Nut_mode' => 'Nut mode',
-'nut_Status_Report' => 'Status Report',
+'nut_Nut_status' => 'Nut status',
 'nut_NutUPS_configuration' => 'NutUPS configuration',
-'nut_APPLY' => 'Apply',
+'nut_Save' => 'Save',
+'nut_SlaveUPS_Password' => 'Secondary->Primary ->Server',
+'nut_SlaveUPS_UPSNAME@IP' => 'Secondary->Primary UPSNAME@IP',
+'nut_SlaveUPS_User' => 'Secondary UPS user',
+'nut_Status_(from_upsc)' => 'Status (from running upsc)',
+'nut_Status_of_the_controlled_UPS' => 'Status of the controlled UPS',
+'nut_STATUS_panel_action_was_successful' => 'STATUS panel action was successful',
+'nut_Status_Report' => 'Status Report',
 'nut_UPS_Device' => 'UPS Device',
 'nut_UPS_Generic_Manufacturer' => 'UPS Generic Manufacturer',
-'nut_Status_of_the_controlled_UPS' => 'Status of the controlled UPS',
+'nut_UPS_Generic_Model' => 'UPS Generic Model',
-'nut_Save' => 'Save',
+'nut_UPS_Generic_Type' => 'UPS Generic Type',
-'nut_status_is_disabled' => 'Nut disabled',
+'nut_UPS_Model' => 'UPS Model',

root/usr/share/smanager/themes/default/public/js/nutups.js

@@ -1,12 +1,16 @@
 $(document).ready(function() {
     function toggleUPSClasses() {
         var selectedOption = $('#Nutmode_select').val();
+        var upsModelValue = $('#UPS_Model_select').val().toLowerCase(); // Get the current value from UPS_Model
         $('.masterups').toggle(selectedOption === 'netserver' || selectedOption === 'standalone'); // Show/Hide masterups based on Net Server or Standalone
+        $('.secondaryups').toggle(selectedOption === 'netserver' ); // Show/Hide Secondary logins for net server
         $('.slaveups').toggle(selectedOption === 'netclient'); // Show/Hide slaveups based on Net Client
+        $('.generics').toggle(selectedOption !== 'netclient' && upsModelValue === 'genericups' );
 
         // Enable/Disable inputs based on the selected option
         $('.masterups input').prop('disabled', !(selectedOption === 'netserver' || selectedOption === 'standalone')); 
         $('.slaveups input').prop('disabled', selectedOption !== 'netclient'); 
+        $('.generics input').prop('disabled', selectedOption === 'netclient');
     }
 
     function toggleGenerics() {

root/usr/share/smanager/themes/default/templates/partials/_nut_CONFIG.html.ep

@@ -2,123 +2,135 @@
 %# Generated by SM2Gen version:0.9(20Jan2025) Chameleon version:4.5.4 On Python:3.12.3 at 2025-01-20 16:21:33
 %#
 <div id="Nutups-CONFIG" class="partial Nutups-CONFIG">
-	<script>
+    <script>
-		window.onload = function() {
+        window.onload = function() {
-		SelectInput(); 
+        SelectInput();
-	};
+    };
-	</script>
+    </script>
-	% if (config->{debug} == 1) {
+    % if (config->{debug} == 1) {
-		<pre>
+        <pre>
-			%= dumper $nut_data
+            %= dumper $nut_data
-		</pre>
+        </pre>
-	% }
+    % }
-	% my $btn = l('nut_APPLY');
+    % my $btn = l('nut_APPLY');
-	%= form_for "nutupsu" => (method => 'POST') => begin
+    %= form_for "nutupsu" => (method => 'POST') => (autocomplete => "off" ) => begin
-		% param 'trt' => $nut_data->{trt} unless param 'trt';
+        % param 'trt' => $nut_data->{trt} unless param 'trt';
-		%= hidden_field 'trt' => $nut_data->{trt}
+        %= hidden_field 'trt' => $nut_data->{trt}
-		%# Inputs etc in here.
+        %# Inputs etc in here.
 
-		<h2 class='subh2'><%=l('nut_Manage_Nutups-config_settings:')%></h2>
+        <h2 class='subh2'><%=l('nut_Manage_Nutups-config_settings:')%></h2>
 
-		<p><span class=label>
+        <p><span class=label>
-			%=l('nut_Nut_status')
+            %=l('nut_Nut_status')
-		</span><span class=data>
+        </span><span class=data>
-			%# my @status_options = [['Disabled' => 'disabled'], ['Enabled' => 'enabled']];
+            %# my @status_options = [['Disabled' => 'disabled'], ['Enabled' => 'enabled']];
-			%# param 'status' => $nut_data->{status} unless param 'status';
+            %# param 'status' => $nut_data->{status} unless param 'status';
 
-			% my @status_options = selected_field([['Disabled' => 'disabled'], ['Enabled' => 'enabled']], $nut_data->{status});
+            % my @status_options = selected_field([['Disabled' => 'disabled'], ['Enabled' => 'enabled']], $nut_data->{status});
-			%= select_field 'status' => @status_options, class => 'input', id => 'status_select'
+            %= select_field 'status' => @status_options, class => 'input', id => 'status_select'
-		<br></span>	</p>
+        <br></span>	</p>
 
-		<p><span class=label>
+        <p><span class=label>
-			%=l('nut_Nut_mode')
+            %=l('nut_Nut_mode')
-		</span><span class=data>
+        </span><span class=data>
-			% my @Nutmode_options = [['Standalone' => 'standalone'], ['Net Server' => 'netserver'], ['Net Client ' => 'netclient']];
+            % my @Nutmode_options = [['Standalone' => 'standalone'], ['Net Server' => 'netserver'], ['Net Client ' => 'netclient']];
-			% param 'Nutmode' => $nut_data->{Nutmode} unless param 'Nutmode';
+            % param 'Nutmode' => $nut_data->{Nutmode} unless param 'Nutmode';
-			%= select_field 'Nutmode' => @Nutmode_options, class => 'input', id => 'Nutmode_select'
+            %= select_field 'Nutmode' => @Nutmode_options, class => 'input', id => 'Nutmode_select'
-		<br></span>	</p>
+        <br></span>	</p>
 
-		<div class=masterups>
+        <div class=masterups>
-			<h2 class='subh3'><%=l('nut_if_Net_Server')%></h2>
+            <div class=secondaryups>
+                    <h2 class='subh3'><%=l('nut_if_Net_Server')%></h2>
+                    <p><span class=label>
+                        %=l('nut_MasterUPS_UPSNAME@IP')
+                    </span><span class=data>
+                        % param 'MasterUPS_Name' => $nut_data->{MasterUPS_Name} unless param 'MasterUPS_Name';
+                        %= 'ups@'. $nut_data->{'localip'}
+                    <br></span></p>
 
-			<p><span class=label>
+                    <p><span class='label'>
-				%=l('nut_MasterUPS_UPSNAME@IP')
+                        %=l('nut_SlaveUPS_User')
-			</span><span class=data>
+                    </span><span class=data>
-				% param 'MasterUPS_Name' => $nut_data->{MasterUPS_Name} unless param 'MasterUPS_Name';
+                        %=  'upssecondary'
-				%= text_field 'MasterUPS_Name', size => '50', class => 'textinput MasterUPS_Name' , pattern=>'.*' , placeholder=>'ups@localhost'
+                    </span></p>
-			<br></span></p>
 
-			<p><span class='label'>
+                    <p><span class='label'>
-				%=l('nut_MasterUPS_Password')
+                        %=l('nut_SlaveUPS_Password')
-			</span><span class=data>
+                    </span><span class=data>
-				% param 'MasterUPS_Password' => $nut_data->{MasterUPS_Password} unless param 'MasterUPS_Password';
+                        <%= $nut_data->{'SlaveUPS_Pass'}%>
-				%=password_field 'MasterUPS_Password', class => 'pass6 sme-password'
+                    </span></p>
-			</span></p>
+            </div>
+            <div>
+                <h2><%= l ('nut_UPS_Device') %></h2>
+                <p><span class=label>
+                    %=l('nut_UPS_Model')
+                </span><span class=data>
+                    % my @UPS_Model_options = $c->get_model_options();
+                    % param 'UPS_Model' => $nut_data->{UPS_Model} unless param 'UPS_Model';
+                    %= select_field 'UPS_Model' => \@UPS_Model_options, class => 'input', id => 'UPS_Model_select'
+                <br></span>	</p>
 
-			<p><span class=label>
+                <p><span class=label>
-				%=l('nut_UPS_Model')
+                    %=l('nut_UPS_Device')
-			</span><span class=data>
+                </span><span class=data>
-				% my @UPS_Model_options = $c->get_model_options();
+                    % param 'UPS_Device' => $nut_data->{UPS_Device} unless param 'UPS_Device';
-				% param 'UPS_Model' => $nut_data->{UPS_Model} unless param 'UPS_Model';
+                    %= text_field 'UPS_Device', size => '50', class => 'textinput UPS_Device' , pattern=>'.*' , placeholder=>'auto (for usb)'
-				%= select_field 'UPS_Model' => \@UPS_Model_options, class => 'input', id => 'UPS_Model_select'
+                <br></span></p>
-			<br></span>	</p>
+            </div>
+        </div>
 
-			<p><span class=label>
+        <div class=slaveups>
-				%=l('nut_UPS_Device')
+            <h2 class='subh4'><%=l('nut_if_Net_Client')%></h2>
-			</span><span class=data>
+            <p><span class=label>
-				% param 'UPS_Device' => $nut_data->{UPS_Device} unless param 'UPS_Device';
+                %=l('nut_SlaveUPS_UPSNAME@IP')
-				%= text_field 'UPS_Device', size => '50', class => 'textinput UPS_Device' , pattern=>'.*' , placeholder=>'auto (for usb)'
+            </span><span class=data>
-			<br></span></p>
+                % param 'ClientUPS_Name' => $nut_data->{ClientUPS_Name} unless param 'ClientUPS_Name';
-		</div>
+                %= text_field 'ClientUPS_Name', size => '50', class => 'textinput ClientUPS_Name' , pattern=>'.*' , placeholder=>'upsname@IP[:port]'
+            <br></span></p>
 
-		<div class=slaveups>
+            <p><span class='label'>
-			<h2 class='subh4'><%=l('nut_if_Net_Client')%></h2>
+                %=l('nut_ClientUPS_Username')
-			<p><span class=label>
+            </span><span class=data>
-				%=l('nut_SlaveUPS_UPSNAME@IP')
+                % param 'ClientUPS_User' => $nut_data->{ClientUPS_User} unless param 'ClientUPS_User';
-			</span><span class=data>
+                %=text_field 'ClientUPS_User', class => 'textinput'
-				% param 'SlaveUPS_Name' => $nut_data->{SlaveUPS_Name} unless param 'SlaveUPS_Name';
+            </span></p>
-				%= text_field 'SlaveUPS_Name', size => '50', class => 'textinput SlaveUPS_Name' , pattern=>'.*' , placeholder=>'upsname@IP'
-			<br></span></p>
 
-			<p><span class='label'>
+            <p><span class='label'>
-				%=l('nut_SlaveUPS_Password')
+                %=l('nut_ClientUPS_Password')
-			</span><span class=data>
+            </span><span class=data>
-				% param 'SlaveUPS_Password' => $nut_data->{SlaveUPS_Password} unless param 'SlaveUPS_Password';
+                % param 'ClientUPS_Pass' => $nut_data->{ClientUPS_Pass} unless param 'ClientUPS_Pass';
-				%=password_field 'SlaveUPS_Password', class => 'pass4 sme-password'
+                %=password_field 'ClientUPS_Pass', class => 'pass4 sme-password', autocomplete => 'off'
-			</span></p>
+            </span></p>
-		</div>
+        </div>
 
-		<div class=generics>
+        <div class=generics>
-`			<h2 class='subh5'><%=l('nut_if_genericups')%></h2>
+            <h2 class='subh5'><%=l('nut_if_genericups')%></h2>
-			<p><span class=label>
+            <p><span class=label>
-				%=l('nut_UPS_Generic_Type')
+                %=l('nut_UPS_Generic_Type')
-			</span><span class=data>
+            </span><span class=data>
-				% param 'UPS_gen_Type' => $nut_data->{UPS_gen_Type} unless param 'UPS_gen_Type';
+                % param 'UPS_gen_Type' => $nut_data->{UPS_gen_Type} unless param 'UPS_gen_Type';
-				%= text_field 'UPS_gen_Type', size => '50', class => 'textinput UPS_gen_Type' , pattern=>'.*' , placeholder=>'UPS_gen_Type'
+                %= text_field 'UPS_gen_Type', size => '50', class => 'textinput UPS_gen_Type' , pattern=>'.*' , placeholder=>'UPS_gen_Type'
-			<br></span></p>
+            <br></span></p>
 
-			<p><span class=label>
+            <p><span class=label>
-				%=l('nut_UPS_Generic_Manufacturer')
+                %=l('nut_UPS_Generic_Manufacturer')
-			</span><span class=data>
+            </span><span class=data>
-				% param 'UPS_gen_Mfr' => $nut_data->{UPS_gen_Mfr} unless param 'UPS_gen_Mfr';
+                % param 'UPS_gen_Mfr' => $nut_data->{UPS_gen_Mfr} unless param 'UPS_gen_Mfr';
-				%= text_field 'UPS_gen_Mfr', size => '50', class => 'textinput UPS_gen_Mfr' , pattern=>'.*' , placeholder=>'UPS_gen_Mfr'
+                %= text_field 'UPS_gen_Mfr', size => '50', class => 'textinput UPS_gen_Mfr' , pattern=>'.*' , placeholder=>'UPS_gen_Mfr'
-			<br></span></p>
+            <br></span></p>
 
-			<p><span class=label>
+            <p><span class=label>
-				%=l('nut_UPS_Generic_Model')
+                %=l('nut_UPS_Generic_Model')
-			</span><span class=data>
+            </span><span class=data>
-				% param 'UPS_gen_Model' => $nut_data->{UPS_gen_Model} unless param 'UPS_gen_Model';
+                % param 'UPS_gen_Model' => $nut_data->{UPS_gen_Model} unless param 'UPS_gen_Model';
-				%= text_field 'UPS_gen_Model', size => '50', class => 'textinput UPS_gen_Model' , pattern=>'.*' , placeholder=>'UPS_gen_Model'
+                %= text_field 'UPS_gen_Model', size => '50', class => 'textinput UPS_gen_Model' , pattern=>'.*' , placeholder=>'UPS_gen_Model'
-			<br></span></p>
+            <br></span></p>
-`		</div>
+        </div>
 
-		<span class='data'>
+        <span class='data'>
-			%= submit_button l('nut_Save'), class => 'action subm12'
+            %= submit_button l('nut_Save'), class => 'action subm12'
-		</span>
+        </span>
 
-
+        %# Probably finally by a submit.
-		
+    %end
-	
-		%# Probably finally by a submit.
-	%end    
 </div>

root/usr/share/smanager/themes/default/templates/partials/_nut_STATUS.html.ep

@@ -35,6 +35,8 @@
 		<p class='paragraph para1'>
 			%=l('nut_Descriptive_paragraph')
 		</p>
+		<br />
+
 
 <!--
 		<span class=label>
@@ -45,6 +47,35 @@
 		</span><br>
 -->
 
+    <span class=label>
+      %=l('nut_Nut_mode')
+    </span><span class=data>
+      %= $nut_data->{Nutmode} 
+    </span><br>
+
+      % if ($nut_data->{Nutmode} eq "nutserver") {
+      <div class=secondaryups>
+        <p><span class=label>
+          %=l('nut_MasterUPS_UPSNAME@IP')
+        </span><span class=data>
+          % param 'MasterUPS_Name' => $nut_data->{MasterUPS_Name} unless param 'MasterUPS_Name';
+          %= 'ups@'. $nut_data->{'localip'}
+        <br></span></p>
+
+        <p><span class='label'>
+          %=l('nut_SlaveUPS_User')
+        </span><span class=data>
+          %=  'upssecondary'
+        </span></p>
+
+        <p><span class='label'>
+          %=l('nut_SlaveUPS_Password')
+        </span><span class=data>
+          <%= $nut_data->{'SlaveUPS_Pass'}%>
+        </span></p>
+      </div>
+      % }
+		
 		%= include 'partials/_nut_UPS_STATUS'
 	
 		%# Probably finally by a submit.

root/usr/share/smanager/themes/default/templates/partials/_nut_UPS_STATUS.html.ep

@@ -16,7 +16,17 @@
 			<h2>Battery Status</h2>
 			<table>
 				<tr><td>Charge:</td><td><%= $nut_data->{'ups_data'}->{'battery.charge'} %>%</td></tr>
-				<tr><td>Runtime:</td><td><%= sprintf("%.2f", $nut_data->{'ups_data'}->{'battery.runtime'} / 60) %> minutes</td></tr>
+				%#<tr><td>Runtime:</td><td><%= sprintf("%.2f", $nut_data->{'ups_data'}->{'battery.runtime'} / 60) %> minutes</td></tr>
+				  <td>Runtime:</td>
+				  <td>
+					<% 
+					  my $runtime = $nut_data->{'ups_data'}->{'battery.runtime'};
+					  my $runtime_minutes = (defined $runtime && $runtime =~ /^\d+(\.\d+)?$/) 
+						? sprintf("%.2f", $runtime / 60) 
+						: 'N/A';
+					%>
+					<%= $runtime_minutes %> minutes
+				  </td>
 				<tr><td>Voltage:</td><td><%= $nut_data->{'ups_data'}->{'battery.voltage'} %>V</td></tr>
 				<tr><td>Type:</td><td><%= $nut_data->{'ups_data'}->{'battery.type'} %></td></tr>
 			</table>

smeserver-nutUPS.spec

@@ -4,7 +4,7 @@ Summary: SME server - nut UPS interaction module
 %define name smeserver-nutUPS
 Name: %{name}
 %define version 11.0.0
-%define release 7
+%define release 20
 Version: %{version}
 Release: %{release}%{?dist}
 License: GPL
@@ -12,7 +12,8 @@ Group: Networking/Daemons
 Source: %{name}-%{version}.tar.xz
 
 BuildRoot: /var/tmp/%{name}-%{version}-%{release}-buildroot
-Requires: nut nut-client 
+Requires: nut >= 2.8.2
+Requires: nut-client 
 Obsoletes: neon <= 0.25.5
 Requires: smeserver-lib >= 1.15.1-16
 BuildArchitectures: noarch
@@ -25,8 +26,49 @@ A module which configures the Network UPS Tools suite for operation with
 the SME server software.
 
 %changelog
+* Mon Jul 07 2025 John Crisp <jcrisp@safeandsoundit.co.uk> 11.0.0-20.sme
+- Remove errant backticks
+- Add div to section to enhance formatting in Net Server mode
+
+* Mon Jul 07 2025 Brian Read <brianr@koozali.org> 11.0.0-19.sme
+- Changes from JC (thanks) and also make sure descriptions fit in with Master->Primary and Slave->Secondary [SME: 13069]
+  Also write descriptive paragraph as no-one else has!
+  Also also, incorporate newly auditted lex file
+
+* Fri Jun 13 2025 Brian Read <brianr@koozali.org> 11.0.0-18.sme
+- Adjust call from Custom to be emtpy hash not hashref [SME: 13042]
+
+* Fri Jun 13 2025 Brian Read <brianr@koozali.org> 11.0.0-17.sme
+- Fix return from function in Nutups-custom [SME: 13042]
+- Check Seconds left for zero before dividing by 60 [SME: 13042]
+
+* Fri Jun 13 2025 Brian Read <brianr@koozali.org> 11.0.0-16.sme
+- Change Navigation weighting for SM2 [SME: 12996]
+
+* Wed Jun 11 2025 Jean-Philippe Pialasse <jpp@koozali.org> 11.0.0-15.sme
+- open db flat file using UTF8 [SME: 13035]
+
+* Mon Jun 02 2025 Jean-Philippe Pialasse <jpp@koozali.org> 11.0.0-14.sme
+- fix typo preventing netserver enabling [SME: 13021]
+
+* Wed May 28 2025 Jean-Philippe Pialasse <jpp@koozali.org> 11.0.0-13.sme
+- filter out nut* services from syslog (use journalctl) [SME: 13013]
+
+* Sat May 24 2025 Jean-Philippe Pialasse <jpp@koozali.org> 11.0.0-11.sme
+- fix issue with standalone and netserver mode [SME: 13012]
+
+* Sun May 18 2025 Jean-Philippe Pialasse <jpp@koozali.org> 11.0.0-10.sme
+- add pollinterval setting [SME: 13006]
+- update config for Nut 2.8.2 [SME: 12657]
+
+* Tue Mar 18 2025 Jean-Philippe Pialasse <jpp@koozali.org> 11.0.0-9.sme
+- update config for Nut 2.8.2 [SME: 12657]
+
+* Wed Mar 05 2025 Brian Read <brianr@koozali.org> 11.0.0-8.sme
+- typo in lex file [SME: 12949]
+
 * Mon Mar 03 2025 Brian Read <brianr@koozali.org> 11.0.0-7.sme
-- Enhance UPS Status screen [SME: ]
+- Enhance UPS Status screen [SME: i12949]
 
 * Mon Mar 03 2025 Brian Read <brianr@koozali.org> 11.0.0-6.sme
 - Add in SM2 NutUPS configuration and status panel [SME: 12949]
@@ -97,9 +139,9 @@ the SME server software.
 
 * Thu Jan 22 2015 stephane de Labrusse <stephdl@de-labrusse.fr> 2.4.0-3.sme
 - Remove obsolete directives {ACL,ACCEPT,REJECT} and switch to LISTEN 
-- in /etc/ups/upsd.conf
+ in /etc/ups/upsd.conf
 - Allow NUT in /etc/hosts.allow and in /etc/services [SME: 8793]
-- Code change from  Daniel B.<daniel@firewall-services.com>
+ Code change from  Daniel B.<daniel@firewall-services.com>
 
 * Thu Jan 31 2013 Shad L. Lords <slords@mail.com> 2.4.0-2.sme
 - Obsolete el5 packages that used to be required [SME: 7273]